One of the efficient printing techniques in our society is printing from the screen. It does not matter if it is prepared from paper, silk, or other products. However, Maryland screen printing at times might be challenging to armatures. The article will highlight some of the problems that they are likely to face and the best way to deal with them.
Bleeding of colors is one of the common issues that one might face. It can be frustrating when you find that the colors are moving beyond the area that you want, then it means that the paste you are using is too dilute. For best results, you should use a thick paste one that will not cause any form of bleeding and will give you the desired outcome.
It is frustrating when you find that you have gaps that are not equal when you are doing repeats. Most people think that doing a repeat is something simple, but that is not the case. If you want to do it right then, you should be calculative. Check well and do calculative placement.
If you are new in this scheme, you might not know where to place the repeats. To deal with this, you need to use colored chalk to mark the repeats on that cloth, and this will help one know where they will be placing each repeat. The other solution is placing of colored strands at the edge of the design and when doing a repeat all one need to do is to put the screen directly on the strands.
The other thing that you should watch out for is soiling of the cloth. Note that if you do not block the pores, then you might end up with this problem. That is the reason that you should apply a tape around the edge; it will make the print clean and well done since there will be no spillage on the sides.
Having the colored pigments not being distributed is also another issue that you might end up facing. If this is the situation, you might end up with the formation of patches. If you want to have a paste that is evenly distributed, then it is best to make sure that the pigments you use are enough. The other thing you should do is pull the squeegee well.
Pinholes are another issue that you might face, and the worst part is that no matter how many times you do the repeat they do not go away. This leaves your print looking untidy. One of the reasons that you might face a pinhole is if you do not clean up the mesh. It is important to get rid of any impurities before you start the printing so that you can end up with ideal results.
The coating is also another thing that can be used to create pinholes in the display. However this will not happen if the coating is well done, you should make sure that you do it more than once so that you might get the desired outcome. If you do it once, when washing the fabric, you will find that there are pinholes. Thus, it is best to have a repeat once or twice before you get the developing done.
Bleeding of colors is one of the common issues that one might face. It can be frustrating when you find that the colors are moving beyond the area that you want, then it means that the paste you are using is too dilute. For best results, you should use a thick paste one that will not cause any form of bleeding and will give you the desired outcome.
It is frustrating when you find that you have gaps that are not equal when you are doing repeats. Most people think that doing a repeat is something simple, but that is not the case. If you want to do it right then, you should be calculative. Check well and do calculative placement.
If you are new in this scheme, you might not know where to place the repeats. To deal with this, you need to use colored chalk to mark the repeats on that cloth, and this will help one know where they will be placing each repeat. The other solution is placing of colored strands at the edge of the design and when doing a repeat all one need to do is to put the screen directly on the strands.
The other thing that you should watch out for is soiling of the cloth. Note that if you do not block the pores, then you might end up with this problem. That is the reason that you should apply a tape around the edge; it will make the print clean and well done since there will be no spillage on the sides.
Having the colored pigments not being distributed is also another issue that you might end up facing. If this is the situation, you might end up with the formation of patches. If you want to have a paste that is evenly distributed, then it is best to make sure that the pigments you use are enough. The other thing you should do is pull the squeegee well.
Pinholes are another issue that you might face, and the worst part is that no matter how many times you do the repeat they do not go away. This leaves your print looking untidy. One of the reasons that you might face a pinhole is if you do not clean up the mesh. It is important to get rid of any impurities before you start the printing so that you can end up with ideal results.
The coating is also another thing that can be used to create pinholes in the display. However this will not happen if the coating is well done, you should make sure that you do it more than once so that you might get the desired outcome. If you do it once, when washing the fabric, you will find that there are pinholes. Thus, it is best to have a repeat once or twice before you get the developing done.
About the Author:
Find a summary of the advantages you get when you use Maryland screen printing services and more information about a reputable printing company at http://spnprints.com/services.html now.
No comments:
Post a Comment